How to Get Free CCNP SWITCH 300-115 Dumps

Kill4exam now, offers one year associated with free of charge changes to get Cisco 300-115 exam materials. Each of our Cisco 300-115 exam sample questions can help you get professional inside of virtually no time. Whenever you adapt the rapidshare along with Cisco 300-115 questions and answers, you’ll be aware the visible difference. http://www.kill4exam.com/300-115.html  Cisco 300-115 exam sample questions are ready simply by Industry experts along with Specialists providing you the top road to being successful using swiftest changes in step with Cisco 300-115 vce. Cisco 300-115 Certification is usually attaining significantly magnitude from it industry each day. HRCI authenticates knowing, ability, abilities along with features.

QUESTION 17
An administrator recently configured all ports for rapid transition using PortFast. After testing, it has been determined that several ports are not transitioning as they should. What is the reason for this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.

Correct Answer: C Explanation  1z0-803 exam
Explanation/Reference:
Explanation: RSTP can only achieve rapid transition to the forwarding state on edge ports and on point-to- point links, not on trunk links. The link type is automatically derived from the duplex mode of a port. A port that operates in full-duplex is assumed to be point-to-point, while a half-duplex port is considered as a shared port by default. This automatic link type setting can be overridden by explicit configuration. In switched networks today, most links operate in full-duplex mode and are treated as point-to-point links by RSTP. This makes them candidates for rapid transition to the forwarding state. Reference:
QUESTION 18
Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Correct Answer: C Explanation Explanation/Reference:  http://www.itcertlab.com/pass-cisco-200-120-ccna-pdf-quick-and-easy.html

Explanation: VTP pruning enhances network bandwidth use by reducing unnecessary flooded traffic, such as broadcast, multicast, unknown, and flooded unicast packets to only the switches that require it. VTP pruning increases available bandwidth by restricting flooded traffic to those trunk links that the traffic must use to access the appropriate network devices. By default, VTP pruning is disabled. Reference:

300-115 vce
QUESTION 19
What effect does the mac address-table aging-time 180 command have on the MAC address- table?
A. This is how long a dynamic MAC address will remain in the CAM table.
B. The MAC address-table will be flushed every 3 minutes.
C. The default timeout period will be 360 seconds.
D. ARP requests will be processed less frequently by the switch.
E. The MAC address-table will hold addresses 180 seconds longer than the default of 10 minutes.

Correct Answer: A Explanation
Explanation/Reference:
Explanation: You can configure the amount of time that an entry (the packet source MAC address and port that packet ingresses) remain in the MAC table. To configure the aging time for all MAC addresses, perform this task: Command Purpose Step 1 switch# configure Enters configuration mode. terminal Step 2 switch(config)# mac- Specifies the time before an entry ages out address-table aging- and is discarded from the MAC address table. time seconds [vlan The range is from 0 to 1000000; the default is vlan_id] 300 seconds. Entering the value 0 disables the MAC aging. If a VLAN is not specified, the aging specification applies to all VLANs. This example shows how to set the aging time for entries in the MAC address table to 600 seconds (10 minutes): switch# configure terminal switch(config)# mac-address-table aging-time 600 Reference:
QUESTION 20
While working in the core network building, a technician accidently bumps the fiber connection between two core switches and damages one of the pairs of fiber. As designed, the link was placed into a non-forwarding state due to a fault with UDLD. After the damaged cable was replaced, the link did not recover. What solution allows the network switch to automatically recover from such an issue?
A. macros
B. errdisable autorecovery
C. IP Event Dampening
D. command aliases
E. Bidirectional Forwarding Detection

Correct Answer: B Explanation
Explanation/Reference:
Explanation: http://www.braindumpscity.com/most-accurate-cisco-300-115-dumps.html
There are a number of events which can disable a link on a Catalyst switch, such as the detection of a loopback, UDLD failure, or a broadcast storm. By default,
manual intervention by an administrator is necessary to restore the interface to working order; this can be done by issuing shutdown followed by no shutdown on
the interface. The idea behind requiring administrative action is so that a human engineer can intercede, assess, and (ideally) correct the issue. However, some
configurations may be prone to accidental violations, and a steady recurrence of these can amount to a huge time sink for the administrative staff.
This is where errdisable autorecovery can be of great assistance. We can configure the switch to automatically re-enable any error-disabled interfaces after a
specified timeout period. This gives the offending issue a chance to be cleared by the user (for example, by removing an unapproved device) without the need for
administrative intervention.
QUESTION 21
A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?
A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.
Correct Answer: C Explanation

Explanation/Reference:
Explanation:
SDM Template Notes:
All templates are predefined. There is no way to edit template category individual values.
The switch reload is required to use a new SDM template.

The ACL merge algorithm, as opposed to the original access control entries (ACEs) configured by the user, generate the number of TCAM entries listed for security and QoS ACEs.

The first eight lines (up to Security ACEs) represent approximate hardware boundaries set when a template is used. If the boundary is exceeded, all processing overflow is sent to the CPU which can have a major impact on the performance of the switch. Choosing the VLAN template will actually disable routing (number of entry for unicast or multicast route is zero) in hardware.
Reference:   http://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/switch2.html
QUESTION 22
An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?
A. VLAN filters are required to ensure traffic mirrors effectively.
B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.
C. The port channel can be used as a SPAN source, but not a destination.
D. RSPAN must be used to capture EtherChannel bidirectional traffic.

Correct Answer: C Explanation
Explanation/Reference:
Explanation: A source port or EtherChannel is a port or EtherChannel monitored for traffic analysis. You can configure both Layer 2 and Layer 3 ports and EtherChannels as SPAN sources. SPAN can monitor one or more source ports or EtherChannels in a single SPAN session. You can configure ports or EtherChannels in any VLAN as SPAN sources. Trunk ports or EtherChannels can be configured as sources and mixed with nontrunk sources. A port-channel interface (an EtherChannel) can be a SPAN source, but not a destination. Reference:

300-115 vce
QUESTION 23
Refer to the exhibit.

What is the result of the configuration?
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load-balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.

Correct Answer: B Explanation
Explanation/Reference:
Explanation:
An etherchannel will form if one end is active and the other is passive. The table below sum- marizes the results for LACP channel establishment based on the
configuration of each side of a link:

LACP Channel Establishment
S1 S2 Established?
On On Yes
Active/Passive Active Yes
On/Active/Passive Not Configured No
On Active No
Passive/On Passive No
Load balancing can only be configured globally. As a result, all channels (manually configured, PagP, or LACP) use the same load-balancing. This is true for the
switch globally, although each switch involved in the etherchannel can have non matching parameters for load balancing. Reference:

We’re certain you will pass your Cisco 300-115 dumps after employing your Cisco 300-115 exam sample questions, with Cisco 300-115  pdf questions and answers from http://www.kill4exam.com/300-115.html ; you will be relax knowing you will be fully ready to defend myself against your Cisco 300-115 exam. Kill4exam Cisco 300-115 exam sample questions are regularly busted intended for updates, accurateness along with commencing content materials.